1 Serial Data transmission seems a bit difficult for those who are new to the world of serial communication and VC++. Long ago, I had searched on codeguru.com for some help on serial data transmission and I got some valuable information. It was my dream to develop a simple class for implementing serial data transmission since then. After getting seven months practical experience in the field of serial communication, I have developed a simple class for implementing serial transmission using WinAPI functions. Before going into the details of this class it is essential to know the basics of serial data transmission. Serial Port In serial data transmission the data is transmitted in serial format with the LSB of the byte to be transmitted, shifted out first among the data bits. The general format for serial transmission is Start Bit + Data Bits + Parity Bit (Optional) + Stop Bit. The Parity bit is optional. It is used for error checking in communication. You can enable or disable parity checking by software modifications. Parallel PortAlso, you can specify which parity you would like to use, either 'EVEN' or 'ODD' through software. The various steps to be performed for sending and receiving data through the serial port of a PC are listed below:- • Open the communication port • Configure the communication port by setting the Baud rate, parity, no. Of data bits, etc. • Set time-outs for communication. • Write data to the port. • Read data from the port. • Close the port. Opening The Serial Port The CreateFile() function opens a communications port. There are two ways to call CreateFile() to open the port - OVERLAPPED and NON-OVERLAPPED. You can open a Communication Port for OVERLAPPED IO operation and NON-OVERLAPPED IO operation. The CSerialCom class is written for NON-OVERLAPPED IO operation. For more details on OVERLAPPED & NON-OVERLAPPED IO, please refer to the MSDN documentation. 6 comments on “ Simple C++ class example using serial port, USB, wireless. The purpose of this article is to describe how to interface to serial port on Win32.; Author. Creating a Serial communication. For example data-reading. ![]() Configuring Serial Ports The most critical phase in serial communication programming is configuring the port settings with the DCB structure. Erroneously initializing the DCB structure is a common problem. When a serial communications function does not produce the expected results, the DCB structure may be in error. A call to the CreateFile() function opens a serial port with default port settings. Usually, the application needs to change the defaults. You must set the Baud rate for communication, Parity functions, no. Of Stop Bits, etc. In accordance with the requirements of the external device by calling appropriate WinAPI functions. Configuring Time-Outs An application must always set communication time-outs using the COMMTIMEOUTS structure each time it opens a communication port. If this structure is not configured, the port uses default time-outs supplied by the driver, or time-outs from a previous communication application. By assuming specific time-out settings when the settings are actually different, an application can have read/write operations that never complete or complete too often. You must configure the read & write time-outs by calling the appropriate WinAPI functions. Writing to a Serial Port The WriteFile() function transfers data through the serial connection to another device. Before calling this function, an application must open and configure a serial port. ![]() Serial Port PurposeReading from a Serial Port An application calls the ReadFile() function to receive data from a device at the other end of a serial connection. Closing a Serial Port You must close the communications port after serial transmission in order to make this port available for other applications which use this resource. As long as you are working with a port (i.e. The port is in an open state), other threads or applications will not be able to access to this port till you close the handle to that port in NON-OVERLAPPED IO operation. Call the CloseHandle() function to close the serial port. CloseHandle() has one parameter, which is the handle returned by the CreateFile() call that opened the port. Avery template 74541 indesign: software free download. Additional Information • Depending on what internet browser you are using, your project will either automatically save to your Downloads folder (found on your computer: C: Users *yourname* Downloads) or ask you where you would like to save the file • Your file will be named using the following structure: Avery_*code*_WordTemplate.doc • Please see our to set your printer settings correctly to achieve a successful print job • If you would like to have more freedom when designing your labels, you may find Avery’s free software Design & Print to be a better solution. CSerialCom Class The CSerialCom class uses six member functions to achieve the above mentioned functionality. Collapse| // Open Communication Port. Please check functions return value to ensure whether // Port opened successfully. Port.OpenPort( ); // Configure Port for Communication. Please check functions return value to // ensure whether Port is configured successfully. Port.ConfigurePort( ); // Set communication time outs. Please check functions return // value to ensure whether communication time outs configured // successfully.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |